Application
Designed for installation on potable water lines to reduce high inlet pressure to a lower outlet pressure. The integral strainer makes this device most suitable for residential and commercial water systems that require frequent cleaning of sediment and debris. The direct acting integral by-pass design prevents buildup of excessive system pressure caused by thermal expansion. The balance piston design enables the regulator to react in a smooth and responsive manner to changes in system flow demand, while at the same time, providing protection from inlet pressure changes.
Standards Compliance
Local codes shall govern installation requirements. Unless otherwise specified, the assembly shall be mounted in accordance with the latest edition of the Uniform Plumbing Code. The Model NR3 may be installed in any position. If installed in a pit, vault, or indoors, specify the “SC” sealed cage option. The assembly shall be installed with sufficient side clearance for testing and maintenance. Multiple installations are recommended for wide demand variations or where the desired pressure reduction is more than 4 to 1 (i.e.: 200 psi inlet reduced to 50 psi outlet). CAUTION: Anytime a reducing valve is adjusted, a pressure gauge must be used downstream to verify correct pressure setting. Do not bottom adjustment bolt on bell housing.
Specifications
The Water Pressure Reducing Valve shall be ASSE® Listed 1003, and available with single union, double union and less union end connections. The main body shall be cast bronze (ASTM B 584) alloy. The bell shall be composite plastic. The cartridge shall be acetal and incorporate an integral seat. The seat disc elastomer shall be EPDM. The assembly shall be accessible for maintenance without removing the device from the line. The Water Pressure Reducing Valve shall be a WILKINS Model NR3.
Designed for installation on potable water lines to reduce high inlet pressure to a lower outlet pressure. The integral strainer makes this device most suitable for residential and commercial water systems that require frequent cleaning of sediment and debris. The direct acting integral by-pass design prevents buildup of excessive system pressure caused by thermal expansion. The balance piston design enables the regulator to react in a smooth and responsive manner to changes in system flow demand, while at the same time, providing protection from inlet pressure changes.
Standards Compliance
- ASSE® Listed 1003
- IAPMO® Listed
- CSA® Certified
Local codes shall govern installation requirements. Unless otherwise specified, the assembly shall be mounted in accordance with the latest edition of the Uniform Plumbing Code. The Model NR3 may be installed in any position. If installed in a pit, vault, or indoors, specify the “SC” sealed cage option. The assembly shall be installed with sufficient side clearance for testing and maintenance. Multiple installations are recommended for wide demand variations or where the desired pressure reduction is more than 4 to 1 (i.e.: 200 psi inlet reduced to 50 psi outlet). CAUTION: Anytime a reducing valve is adjusted, a pressure gauge must be used downstream to verify correct pressure setting. Do not bottom adjustment bolt on bell housing.
Specifications
The Water Pressure Reducing Valve shall be ASSE® Listed 1003, and available with single union, double union and less union end connections. The main body shall be cast bronze (ASTM B 584) alloy. The bell shall be composite plastic. The cartridge shall be acetal and incorporate an integral seat. The seat disc elastomer shall be EPDM. The assembly shall be accessible for maintenance without removing the device from the line. The Water Pressure Reducing Valve shall be a WILKINS Model NR3.
Unit of Measure
Specifications
Size |
N/A 1/2 in3/4 in1 in1 1/4 in1 1/2 in2 in |
Main Valve Body |
N/A Cast bronze ASTM B 584, UNS C84400 |
Bell Housing |
N/A UV resistant polymer composite |
Internals |
N/A Stainless steel, 300 Series |
Stem |
N/A Brass ASTM B 16 |
Elastomers |
N/A
EPDM (FDA approved) Buna nitrile (FDA approved) |
Cartridge |
N/A Delrin™ (NSF Listed) |
Springs |
N/A Oil temp wire, ASTM A 229 |
Strainer Screen |
N/A 300 Series Stainless Steel |
Maximum Working Water Pressure |
N/A 300 psi (1 1/2" - 2") 400 psi (1/2" - 1 1/4") |
Minimum Inlet Pressure (As Per UPC Code) |
N/A 80 psi |
Maximum Working Water Temperature |
N/A 140 ºF |
Reduced Pressure Range |
N/A 15 to 75 psi (1/2" - 1 1/4") 25 to 75 psi (1 1/2" - 2") |
Factory Preset |
N/A 50 psi |
Threaded Connections (FNPT) |
N/A ANSI B1.20.1 |
Copper Connections (FC) |
N/A ANSI B16.22 |
Maximum Hot Water Temperature at 100 psi (CPVC Tailpiece) |
N/A 140 ºF |
Cold Water Rated Temperature at 400 psi (CPVC Tailpiece) |
N/A 73.4 ºF |
Accessories |
N/A
BR4DUSPC, Special Plastic Spacer Nipple BR4DUSPC, Steel Pipe item-5277, Repair Kit NR3DUSPC, Steel Pipe NR3DUSPC, Steel Pipe TPK, Tailpiece Kit |
Options |
N/A C - With FC (Copper Sweat) Union Connection CPVC - CPVC tailpiece connection (1") DM - With Double Male 3/4" & 1" Meter Threads Connection DMSS - DM with SS Spring & Sealed Cage DU - With Double Union Connection (FNPT) G - Tapped with Gauge HRSC - High Range 15-150 PSI (1/2"-1 1/4" only) with Sealed Cage LU - With Integral FNPT Connection (No union) P - Tapped and Plugged for Gauge PEX - With Male Barbed Connection Tailpiece for Crossed-linked Polyethylene Tubing SC - With SS Adjustment Bolt and Lock Nut, with SS Spring for below-ground Installations Standard with Single Union FNPT Connection and 20 Mesh Strainer Screen |
