• Model 711F Class 125 Globe Valve

    The Apollo Model 711F Flanged Cast Iron Globe valve provides efficient throttling capabilities. The Apollo Globe valve can reliably be installed in most plumbing and heating systems (or building service piping).

    Features

    • Compatible with ANSI 125# & 150# Flanges
    • Full Port
    • Bronze Mounted Seat Rings
    • Positive Shut-off
    • Throttling Capabilities
    • Adjustable Graphite Stem Packing
    • Outside Screw & Yoke
    • Flanged Connection
    • Bolted Bonnet
    • Rugged Iron Hand Wheel
    • Back Seat Protection
    Standards
    • MSS SP-85, "Gray Iron Globe & Angle Valves Flanged and Threaded Ends"
    • ASME B16.10, "Face-to-Face and End-to-End Dimensions of Valves"
    Performance Rating
    • Saturated Steam: 125 psi (8.6 Bar) to 353ºF (178ºC)
    • Cold Working Pressure: 200 psi (13.8 Bar) at 100ºF
    • Temperature Range: -20ºF to 406ºF

  • Model 610F Class 125 Gate Valve

    The Apollo Model 610F Flanged Cast Iron Gate valve provides full flow capabilities. The Apollo Gate valve can reliably be installed in most plumbing and heating systems (or building service piping).

    Features

    • Compatible with ANSI 125# & 150# Flanges
    • Full Port
    • Bronze Mounted Seat Rings
    • Solid Wedge
    • Adjustable Graphite Stem Packing
    • Non-Rising Stem
    • Flanged Connection
    • Bolted Bonnet
    • Rugged Iron Hand Wheel
    • Back Seat Protection
    Standards
    • MSS SP-70, "Gray Iron Gate Valves Flanged and Threaded"
    • ASME B16.10, "Face-to-Face and End-to-End Dimensions of Valves"
    Performance Rating
    • Saturated Steam: 125 psi (8.6 Bar) to 353ºF(178ºC) (2"-12")
      100 psi (6.9 Bar) to 338ºF(170ºC) (14"-24")
    • Cold Working Pressure: 200 psi (13.8 Bar) at 100ºF (2"-12")
      150 psi (10.3 Bar) at 100ºF (14"-24")
    • Temperature Range: -20ºF to 406ºF

  • Merit Brass ASME Class 150 & 300 Flanged End Ball Valve

    2 - PC Body, Flanged End Ball Valve, Full Port

    Design Features:

    • Built-in ISO 5211 Mounting Pad for Easy Automation
    • Anti-Static Devices for Ball-Stem-Body
    • Blow-out Proof Stem
    • Pressure Balance Hole in Ball Slot
    • Casting Boss on Body for Draining
    Applicable Standards:
    • Design: ASME B16.34, API 608
    • Face to Face: ASME B16.10
    • Wall Thickness: ASME B16.34
    • End Flange: ASME B16.5
    • Inspection & Testing : API 598

  • Merit Brass ASME Class 150 & 300 Flanged End Ball Valve

    2 - PC Body, Flanged End Ball Valve, Full Port

    Design Features:

    • Built-in ISO 5211 Mounting Pad for Easy Automation
    • Anti-Static Devices for Ball-Stem-Body
    • Blow-out Proof Stem
    • Pressure Balance Hole in Ball Slot
    • Casting Boss on Body for Draining
    Applicable Standards:
    • Design: ASME B16.34, API 608
    • Face to Face: ASME B16.10
    • Wall Thickness: ASME B16.34
    • End Flange: ASME B16.5
    • Inspection & Testing : API 598

  • Model 950XLT - Top Access Double Check Valve Assembly

    Application
    Designed for installation on potable water lines to protect against both back siphonage and backpressure of polluted water into the potable water supply. A tethered test cock cap is provided to protect against fouling caused by insects, dirt and debris. Assembly shall provide protection where a potential non-health hazard exists.

    Standards Compliance
    (Unless otherwise noted, applies to 3/4" thru 2" Horizontal)

    • ASSE® Listed 1015 (Vertical flow-up:1 1/4" thru 2")
    • IAPMO® Listed
    • AWWA Compliant C510
    • CSA® Certified (Vertical flow-up:1 1/2" & 2")
    • NYC MEA 426-89-M VOL 3
    • Approved by the Foundation for Cross Connection Control and Hydraulic Research at the University of Southern California
    Typical Installation
    Local codes shall govern installation requirements. To be installed in accordance with the manufacturer's instructions and the latest edition of the Uniform Plumbing Code. Unless otherwise specified, the assembly shall be mounted at a minimum of 12" (305mm) and a maximum of 30" (762mm) above adequate drains with sufficient side clearance for testing and maintenance. If installed below grade, be certain adequate drainage is provided to prevent the device from being submerged.

    Specifications
    The Double Check Type Backflow Preventer shall be ASSE Listed 1015, rated to 180ºF and supplied with full port ball valves. The main body and access covers shall be bronze (ASTM B 584), the seat ring and all internal polymers shall be NSF® Listed Noryl™ and the seat disc elastomers shall be SILICONE. The first and second check shall be located at a 45º angle and accessible for maintenance from the top of the device, without removing the device from the line. Each check shall have separate access covers and test cocks shall be accessible from the top of the device. Test cocks shall be protected from debris by a tethered cap. The Double Check Type Backflow Preventer shall be a WILKINS Model 950XLT.