Size Range: 1/2" through 4"
Material: Carbon steel
Finish: Copper plated, also available in yellow dichromate.
Service: Recommended for suspension of non-insulated stationary copper tube.
Approvals: Complies with Federal Specification A-A-1192A (Type 10) WW-H-171-E (Type 10) and MSS-SP-69 (Type 10).

Features:

• Threads are countersunk so that they cannot become burred or damaged.
• Knurled swivel nut provides vertical adjustment after piping is in place.
• Captured swivel nut will not fall off.

Ordering: Specify nominal tube size, figure number, name and finish. Metric nut available upon request.

Size Range: 1/2" through 3"
Material: Malleable iron
Finish: Copper plated
Service: Recommended for suspension of non-insulated stationary copper tube. May be used with rod socket or turnbuckle adjuster
Approvals: Complies with Federal Specification A-A-1192A (Type 11) WW-H-171-E (Type 11) and MSS-SP-69 (Type 11).
Service: The split tubing ring Fig. CT-109 is used for suspension of tubing on many installations where it is necessary to specify universally adaptable parts. May be used with rod socket Fig. 110R or turnbuckle adjuster Fig. 114.
Ordering: Specify nominal tube size, figure number, name.

Size Range: 1/2" through 2"
Material: Malleable iron
Finish: Copper plated
Service: Recommended for suspension of non-insulated stationary copper tube.
Approvals: Complies with Federal Specification A-A-1192A (Type 12) WW-H-171-E (Type 25) and MSS-SP-69 (Type 12).

Installation:

• Permanent installation of clamp may be made before the tubing is placed in position.
• Final installation is attained by swinging the lower portion of the hinged clamp up under the tubing and inserting a single screw securely.

Features:

• Hinged design provides for economical installation.
• Designed to provide a tight fit on copper tubing.

Ordering: Specify nominal tube size, figure number, name.

Size Range: 1/2" through 4"
Material: Carbon steel ring and malleable iron adjusting nut.
Finish: Copper plated
Service: Recommended for suspension of non-insulated stationary copper tube.
Approvals: Complies with Federal Specification A-A-1192A (Type 9) WW-H-171-E (Type 9) and MSS-SP-69 (Type 9).
Installation: Full load carrying capacity is reached when the rod is screwed to the bottom of the opening in the nut.

Features:

• Large sight hole provides means of assuring thread engagement.
• Sized for copper tubing.
• Greater vertical adjustability.
• Nut may be attached to rod before pipe is picked up in band and snapped into position.
• Competitively priced.

Ordering: Specify nominal tube size, figure number, name.

Size Range: 1/2" through 4"
Material: Carbon steel ring and malleable iron adjusting nut.
Finish: Copper plated with the band plastic coated.
Features: Eliminates possibility of galvanic action between hanger and copper tubing.
Ordering: Specify nominal tube size, figure number, name.

Size Range: 1/2" through 4"
Material: Carbon steel
Finish: Copper plated, also available in yellow dichromate and plastic coated.
Service: Recommended for suspension of non-insulated, stationary copper tube.
Approvals: Complies with Federal Specification WW-H-171-E (Type 12).
Installation:
(1) Adjustment may be made either before or after tubing is in place without temporary support of pipe.
(2) Hanger rod and nuts may be locked into position after adjustment by use of the upper nut.
Features: Provides for adjustment up to 1 7/8
Ordering: Specify nominal tube size, figure number, name and finish.