Size Range: 1/2" through 30"
Material: Carbon steel
Finish: Plain or Galvanized, also available plastic or epoxy coated
Service: Recommended for the suspension of stationary pipe lines.
Maximum Temperature: Plain 650° F, Galvanized and Epoxy 450° F
Approvals: Complies with Federal Specification A-A-1192A (Type 1), WW-H-171-E (Type 1) and MSS-SP-69 (Type 1). UL, ULC Listed and FM Approved (Sizes 3/4" through 8").
Installation: Hanger load nut above clevis must be tightened securely to assure proper hanger performance. When an oversized clevis is used, a pipe spacer should be placed over the clevis bolt as a spacer to assure that the lower U-strap will not move in on the bolt. For ductile iron pipe sizes, see Figure 590.
Adjustment: Vertical adjustment without removing pipe may be made from 3/8" through 5 1/8", varying with the size of clevis. Tighten upper nut after adjustment.

Features:

• Design has yoke on outside of lower U-strap so yoke cannot slide toward center of bolt, thus bending of bolt is minimized.
• Sizes 5" and up have rod and two nuts instead of bolt and nut; thread length on clevis rod is such that the thread locks the nuts in place, and threads are not in shear plane.

Ordering: Specify pipe size, figure number, name and finish.

Punched forming holes may be present on certain sizes of this clevis hanger. These holes are solely for the purpose of manufacturing, and do not effect the structural integrity or load carrying capacities of these hangers.

"Span" represents the maximum recommended distance between hangers on a continuous and straight run of horizontal standard weight steel pipe filled with water. In all cases, verify that chosen location of hangers does not subject hangers to a load greater than the maximum recommended load shown above.

Size Range: 3/8 and 1/2"
Material: Ductile iron, hardened steel cup point set screw and locknut.
Finish: Plain or Galvanized
Service: Recommended for use under roof installations with bar joist type construction, or for attachment to the top or bottom flange of structural shapes where the vertical hanger rod is required to be offset from the edge of the flange and where the thickness of joist or flange does not exceed 3/4".
Approvals: Complies with Federal Specification A-A-1192A (Type 19 & 23) WW-H-171-E (Type 23) and MSS-SP-69 (Type 19 & 23). UL, ULC listed and FM approved.
How to size: Size of clamp is determined by size of rod to be used.
Installation: Follow recommended set screw torque values per MSS-SP-69 (See table on page PH-212)

Features:

• They may be attached to horizontal flanges of structural members in either the top beam or bottom beam positions.
• Secured in place by a cup-pointed Set Screw tightened against the flange. A Jam Nut is provided for tightening the Set Screw against the Body Casting.
• Thru tapping of the body casting permits extended adjustment of the threaded rod.
• Can be used with Fig 89X retaining clip for seismic applications.

Ordering: Specify rod size, figure number, name of clamp and finish.

Size Range: 3/8 and 1/2"
Material: Malleable/Ductile iron clamp, hardened steel cup point set screw and locknut.
Finish: Plain and Galvanized
Service: Recommended for use under roof installations with bar joist type constructions, or for attachment to the top or bottom flange of structural shapes where the vertical hanger rod is required to be offset from the edge of the flange and where the thickness of joist or flange does not exceed 1 1/4".
Approvals: Complies with Federal Specification A-A-1192A (Type 19 & 23)WW-H-171-E (Type 23) and MSS-SP-69 (Type 19 & 23). UL, ULC listed and FM approved.
How to size: Size of clamp is determined by size of rod to be used.
Installation: Follow recommended set screw torque values per MSS-SP-69 (See tables on page PH-212)

Features:

• They may be attached to horizontal flanges of structural members in either the top beam or bottom beam positions.
• Secured in place by a cup-pointed Set Screw tightened against the flange. A Jam Nut is provided for tightening the Set Screw against the Body Casting.
• Thru tapping of the body casting permits extended adjustment of the threaded rod.
• Wider throat for attaching to flange with up to 1 1/4" thickness.

Ordering: Specify rod size, figure number, name of clamp and finish.